Her Hakkı ALTINAY Madencilik İnşaat Gıda Makina Sanayi ve Ticaret A.Ş.'ne aittir.
Pre-feeding bopper, feeding belt conveyor and rotary distributor
Volume : 7 m3
Feeding belt conveyor dimensions : 800x17200 mm
Motor-reduction : 11 kW, 1500 rpm, i: 12
Aggregate Bunker : 1 Unit
Volume : 40 m3
The number of compartments : 4 x 10 m3
Discharge chute : 1 units / compartment
Pneumatic Piston : 1 Unit, MAG
FRY Air Preparation Unit : 1 Unit MAG
Sand Vibrator : 1 Unit 200/3, MVE
Moisture measuring device : 1 unit, Arnold FSV24-G50 TKI
Weighing Belt Conveyor : 1 Unit
Load cell : 4 x 2000 kg
Dimensions : 600x5000 mm.
Bearings : SNA series with lubrication greaser
Drums : Driving drum covered with10 mm rubber
Weighing bunker vibrators : 1 Unit 200/3, MVE
Motor-Reduction : 5,5 kW, 1500 rpm, i: 12
Weighing bunker and belt conveyor is designed to work under all kinds of loads without any problem.
Dimensions : 600x8000 mm (chevron type belt)
Bearings : SNA series with lubrication greaser
Drums : Driving drum covered with 10 mm rubber
Motor-reduction : 7,5 kW, 1500 rpm, i =12
4- MAIN CHASSIS SUPERSTRUCTURE
Plant chassis with 8-wheels, which provides 4250 mm useful height and has 8 units of wheels, is produced from section - profile and sheet iron, according to ISO9001 and all related DIN norms.
Cement Weighing Hopper : 1 Unit
Load Cell : 3 x 1000 kg
Water Weighing Hopper : 1 Unit
Load Cell : 1 x 1000 kg
Additive Weighing Hopper : 1 Unit
Load Cell : 1 x 60 kg
Pneumatic Equipment : 1 Set
Compressor
1500 lt/min volumetric flow rate
7,5 kW motor power
550 lt depot volume
8 kg/cm2 operating pressure
Pipe and fittings materials
Water equipment : 1 Set
Water equipments on the plant
1½" Pneumatic valve, Valbia
Water pump is not included in this price offer
5- AXIAL MIXER, SINGLE SHAFT
Origin : Turkey
Feeding capacity : 2000 lt
Fresh Concrete Capacity : 1500 lt
Compacted Concrete Capacity : 1000 lt
Motor-Gear Box Power : 37 kW
Water distributor
Pneumatic discharge door
Automatic lubrication system
Safety switch of the maintenance door
6- AUTOMATION SYSTEM OF THE PLANT
BASIC AUTOMATION SYSTEM
- Command and control operations are done by PLC. At the maximum capacity high weighing and dosage sensitivity can be achieved by advanced PLC programs and error control algorithms.
- MCC and command panel is manufactured up to heavy operating conditions and has all kinds of electrical protection.
- All kinds of parameter setup, receipt and calibration operations can be done on operator's panel screen; process, production and failure information can be taken.
- Manuel and automatic operation can be done on illuminated mimic diagram. Voltage and current values can be followed by digital indicators on the panel.
COMPUTERIZED COMMAND AND CONTROL (SCADA) SYSTEM
- All command and control operations, all kind of reporting, failure indications and etc are done by PC Monitor and animation support with PC, printer, UPS and SCADA software.
- Desired amount of receipt can be prepared, customer and truck information can be entered and production information of at least past-one year can be shown.
Capacity : 36 tons
Plate thickness : 4 - 6 mm
Filling pipe : 4 inches
Silo pressure valve : WAM
Level indicators : WAM ILTC220 (top and bottom)
Fluidisation nozzle : WAM-U025, 6 Units/Silo
Mechanical valve : WAM-V2FS250S
FR Filter regulator
½” 220 volt, solenoid valve
Pneumatic pipe installation
Ladder, manhole, platform, and parapets are included.
8- SILO-TOP FILTER : 1 Unit
Filter : 24 m2 JetPulse
Surface area : 24,5 m2
The number of filter cartridges : 7 units
Air filtration flow of 2200-2500 Nm3/hr.
Filter has diameter of ? 800 mm, body made from 1 mm AISI304 material, cleaning system Jet Pulse, electronically control.
Dimension : ø219 x 10000 mm
Motor power : 7,5 kW
Capacity : 60 ton/hour
Mark : WAM
9- CEMENT SCREW CONVEYOR : 1 Unit
10- WATER TANK WITH PUMP : 1 Unit
11- ADDITIVE TANK WITH PUMP : 1 Unit
